Претраживање
Приказ резултата 21-30 од 30
Electrical Properties of Inkjet Printed Graphene Patterns on PET-Based Substrate
(IEEE Computer Society, 2015)
In this paper, electrical properties of inkjet printed graphene patterns on a PET-based (Novele (TM) IJ-220) substrate are presented. Water-soluble graphene conductive ink (Phene plus I3015) was used. Tested samples were ...
Structural and electrical properties of BaCe(0.9)Ee(0.1)O(2.95) electrolyte for IT-SOFCs
(Pergamon-Elsevier Science Ltd, Oxford, 2015)
BaCe(0.9)Ee(0.1)O(2.95) (BCE) nanopowder was synthesized by citric-nitric autocombustion method. Rietveld refinement analysis showed that unit cell volume was slightly larger compared with the most known BaCe0.9Y0.1O2.95, ...
Characterisation of Mn0.63Zn0.37Fe2O4 Powders After Intensive Milling and Subsequent Thermal Treatment
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2017)
Commercial Mn-Zn powder (Mn0.63Zn0.37Fe2O4, 93 wt. % and Fe2O3 7 wt. %) was milled 0.5, 1, 2 and 4 hours in a planetary ball mill. The goal was to observe intensive milling influences on oxidation and reduction processes ...
The characterization of the barium titanate ceramic powders prepared by the Pechini type reaction route and mechanically assisted synthesis
(Elsevier Sci Ltd, Oxford, 2010)
BaTiO3 ceramic powders were prepared by a complex method based on the Pechini type reaction route and mechanically assisted synthesis. In both ways BaTiO3 ceramics were sintered after 120 min on 1300 degrees C without ...
Structure and photocatalytic properties of sintered TiO2 nanotube arrays
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2018)
One-dimensional (1D) TiO2 nanotubes perpendicular to the substrate were obtained by electrochemical oxidation of titanium foil in an acid electrolyte. In order to alter the crystallinity and the morphology of films the ...
Reheating of Zinc-titanate Sintered Specimens
(Međunarodni Institut za nauku o sinterovanju, Beograd, 2015)
The scope of this work was observing dimensional and heat transfer changes in ZnTiO3 samples during heating in nitrogen and air atmosphere. Interactions of bulk specimens with gaseous surrounding induce microstructure ...
Properties of MnZn ferrites prepared by powder injection molding technology
(Elsevier Science Bv, Amsterdam, 2010)
In this work, manganese zinc ferrite components were manufactured by powder injection molding-PIM technology. A fine powder consisting of Mn1-xZnxFe2O4 with small addition of hematite alpha-Fe2O3 as used in mass ferrite ...
Influence of sintering temperature and various atmospheres on structural and electrical properties of LaNi1-xNbxO3 (x = 0.005, 0.05)
(Hot Topics in Contemporary Crystallography 3, HTCC3, workshop, September 23-27, 2018, Bol, Brač, Croatia, 2018)
Ternary lanthanum nickelates, La2NiO4, La3Ni2O7, La4Ni3O10 and LaNiO3 belong to Ruddlesden-Popper (RP) homologous series with the general formula Lan+1NinO3n+1, where n = 1, 2, 3 and ∞, respectively.The crystal structure ...
Pseudobrookite thick films for potential application as low-temperature sensitive material in NO gas sensors
(IEEE Computer Society, 2017)
Pseudobrookite thick films were obtained by screen printing paste composed of a 1: 1.5 molar ratio mixture of starting nanopowders of hematite and anatase, glass frit and organic binder. The films were deposited on alumina ...
Understanding the Effect of Synthesis and Sintering Temperature on the Functional Properties of Barium Titanate/ Cobalt Ferrite Composites
(Association for ETRAN Society, 2023)
To investigate the effect of synthesis procedure and sintering temperature on the functional properties of perovskite/spinel ceramics, BaTiO3/CoFe2O4 composites were prepared by thermal decomposition, coprecipitation, and ...