Претраживање
Приказ резултата 1-10 од 31
Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling
(Elsevier Sci Ltd, Oxford, 2008)
ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 degrees C for 2 h. The influence of the starting powder mixture's composition - the amounts of the ...
Microstructure of LaNiO3 thin films obtained by the spin-on technique from citrate precursors
(Elsevier Sci Ltd, Oxford, 2008)
The morphology of perovskite LaNiO3 (LNO) thin films is a very important feature considering the fact that they could be used as an electrode material in ferroelectric devices. In this work, LNO films were prepared from ...
Comparative study of CeO2 nanopowders obtained by the hydrothermal method from various precursors
(Elsevier Sci Ltd, Oxford, 2015)
The effects of common precursors used in the synthesis of CeO2 nanopowders were investigated, and the structural and spectral properties of the resulting products were compared. Two cerium (III) salts, i.e., Ce(NO3)(3)center ...
Monitoring of transformations in bentonite after NaOH-TMA treatment
(Elsevier Sci Ltd, Oxford, 2007)
Semi-quantitative methods of X-ray diffraction and FTIR-spectroscopy, accompanied by electron microscopy, X-ray microanalysis and others were used to monitor structural-phase reorganizations occurring in a smectite-gypsum ...
Dielectric and magnetic properties of BaTiO3-NiFe2O4 multiferroic composites
(Elsevier Sci Ltd, Oxford, 2014)
Multiferroic composites with the general formula x BaTiO3-(1-x) NiFe2O4 (x=0.5, 0.7, 0.8) were prepared by mixing chemically obtained nickel ferrite and barium titanate powders. Optimum processing parameters for a reduction ...
Densification rate and phase structure changes during sintering of zinc titanate ceramics
(Elsevier Sci Ltd, Oxford, 2009)
Densification rate and phase structure changes during sintering of nanosized ZnTiO3 were studied. Sintering was performed in a dilatometer in two regimes: the first to 900 degrees C (heating rates 5, 10 and 15 degrees ...
Improvement of barium titanate properties induced by attrition milling
(Elsevier Sci Ltd, Oxford, 2012)
Barium titanate powder was prepared by soft chemical process from polymeric precursors (modified Pechini process). The synthesized barium titanate (BT) powder was nanosized and the factor of agglomeration (F-agg) pointed ...
Ex-situ sensitization of ordered TiO2 nanotubes with CdS quantum dots
(Elsevier Sci Ltd, Oxford, 2015)
Ordered titania nanotubes (pore diameter approximate to 90 nm and wall thickness approximate to 10 nm) were obtained by the anodization technique and used for the ex-situ deposition of cadmium sulfide quantum dots (CdS ...
Structural, electrical and magnetic properties of nickel manganite obtained by a complex polymerization method
(Elsevier Sci Ltd, Oxford, 2014)
Structural, electrical and magnetic properties of nickel manganite ceramics obtained by sintering fine powders prepared by a complex polymerization method are given in this work. The phase composition of the synthesized ...
Dielectric and ferroelectric properties of BST ceramics obtained by a hydrothermally assisted complex polymerization method
(Elsevier Sci Ltd, Oxford, 2015)
Ba0.8Sr0.2TiO3 (BST) powder, obtained by a hydrothermal treatment of precursor solution previously prepared by a complex polymerization method (HT-CPM), was uniaxially pressed and sintered at 1280 degrees C for 1-32 h. The ...