Претраживање
Приказ резултата 1-10 од 52
Modeling of the heat loss in a thermal sensor for water made of NTC thick film segmented thermistors
(Trans Tech Publications Ltd, Durnten-Zurich, 2013)
NTC thick film segmented thermistors were realized by screen printing of a low resistivity paste and conductive PdAg paste printed for electrodes. Two thick film thermistors as thermal sensors were placed in plastic tube ...
Ink-Jet Printed Strain Sensor on Polyimide Substrate
(Proceedings of the International Spring Seminar on Electronics Technology, 2013)
This paper describes a method for measuring strain on a specimen with flexible strain sensor. The sensor is made by ink-jet printing of silver ink on polyimide substrate, in that manner providing a combination of electrical ...
Different immobilization methods of soybean hull peroxidase on macroporous glycidyl methacrylate copolymers
(MTG - Topgraf Velika Gorica, 2013)
Wastewater treatment is a current and important environmental issue. Phenolic compounds most of which are
toxic and many even carcinogens, found in various polluted waters are non-biodegradable and present a serious
health ...
Density of the ZnTiO3 nanopowder as a loose powder and as a compact obtained by different methods
(Belgrade : Serbian Ceramic Society, 2013)
Nanopowder density, as well as compact density, is due to powder particle size, different in their values, compared to micron powders. Also, the technique used for density determination induces large mutual value discrepancies. ...
Design and Simulation of 13.56 MHz RFID Tag in Ink-Jet Printing Technology
(IEEE, 2013)
This paper presents design, modeling and simulation cost-effective RFID (Radio Frequency Identification) tag using ink-jet printing technology. Passive 13.56 MHz RFID tag is based on an inductive-capacitive resonant circuit. ...
3 Structural, morphological and electrical properties of sintered Fe2O3/TiO2 nanopowder mixtures
(Belgrade : Institute of Technical Sciences of SASA, 2013)
Starting nanopowders of TiO2 (anatase 99.7%) and a-Fe2O3 (hematite) were mixed in the weight ratio 60:40 and 40:60. Green samples were sintered in the temperature range 750-1250oC in air. Structural, morphological and ...
Optimization and Application of NTC thick film segmented thermistors
(Trans Tech Publications Ltd, Durnten-Zurich, 2013)
NTC thermistor paste for printing thermal sensors on alumina was formed of very fine Ni0.5Cu0.2Zn1.0Mn1.3O4 thermistor powder obtained by a combined mechanical activation/thermal treatment process, organic vehicle and glass ...
SYNTHESIS PROCEDURE AND PROPERTIES OF NiFe2O4 – BaTiO3 COMPOSITES
(Institute for Multidisciplinary Research, University of Belgrade Kneza Višeslava 1, 11000 Belgrade, Serbia, 2013)
NiFe2O4 (NF) powder was prepared by auto combustion method starting from nickel and iron nitrates. After the process of self-ignition, fine precursor powder was thermally treated and forming the nickel ferrite powder. XRD ...
INFLUENCE OF DOPANTS ON BARIUM BISMUTH TITANATE ELECTRICAL PROPERTIES
(Institute for Multidisciplinary Research, University of Belgrade Kneza Višeslava 1, 11000 Belgrade, Serbia, 2013)
The Aurivillius structure has capability to host ions of different size, so a large number of different dopants can be accommodated in the BaBi4Ti4O15 (BBT) lattice. It was detected that various substitutions of Bi3+ and ...
Structural, morphological and optical study of nanostructured TiO2/Fe2O3 thick film
(Bor : Technical Faculty, 2013)
Thick films of nanostructured TiO2 (60 wt%) and alpha-Fe2O3 (40 wt%) were fabricated by screen printing technology on an alumina substrate. Samples were sintered in the temperature range 750-1350oC in air. Thick film paste ...