TY  - CONF
AU  - Srdic, B.
AU  - Stefanov, A.
AU  - Kisic, M.
AU  - Živanov, Ljiljana D
AU  - Menicanin, Aleksandar
PY  - 2021
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1433
AB  - The aim of the work is the realization and modelling of a simple capacitive displacement sensor with the use of 3D printing technology and polylactic acid (PLA) material. The sensor consists of three 3D printed PLA parts: Two electrodes with cavities and a spacer. The silver paste is not printed but micromolded by filling it into the cavities of printed PLA electrodes via a syringe. The capacitance of the fabricated sensor versus applied displacement is measured and compared with calculated capacitance of simple sensor model. A simple model of a sensor capacitor is not capable of describing the behavior of this type of sensor. Therefore, more complex model of sensor capacitor is given better fit to measured results. Additionally, the hysteresis of the fabricated sensor is tested.
PB  - IEEE Computer Society
C3  - Proceedings of the International Spring Seminar on Electronics Technology
T1  - Design and Modelling of 3D Printed Capacitive Displacement Sensor
VL  - 2021-May
DO  - 10.1109/ISSE51996.2021.9467666
ER  - 

@conference{
author = "Srdic, B. and Stefanov, A. and Kisic, M. and Živanov, Ljiljana D and Menicanin, Aleksandar",
year = "2021",
abstract = "The aim of the work is the realization and modelling of a simple capacitive displacement sensor with the use of 3D printing technology and polylactic acid (PLA) material. The sensor consists of three 3D printed PLA parts: Two electrodes with cavities and a spacer. The silver paste is not printed but micromolded by filling it into the cavities of printed PLA electrodes via a syringe. The capacitance of the fabricated sensor versus applied displacement is measured and compared with calculated capacitance of simple sensor model. A simple model of a sensor capacitor is not capable of describing the behavior of this type of sensor. Therefore, more complex model of sensor capacitor is given better fit to measured results. Additionally, the hysteresis of the fabricated sensor is tested.",
publisher = "IEEE Computer Society",
journal = "Proceedings of the International Spring Seminar on Electronics Technology",
title = "Design and Modelling of 3D Printed Capacitive Displacement Sensor",
volume = "2021-May",
doi = "10.1109/ISSE51996.2021.9467666"
}

Srdic, B., Stefanov, A., Kisic, M., Živanov, L. D.,& Menicanin, A.. (2021). Design and Modelling of 3D Printed Capacitive Displacement Sensor. in Proceedings of the International Spring Seminar on Electronics Technology
IEEE Computer Society., 2021-May.
https://doi.org/10.1109/ISSE51996.2021.9467666

Srdic B, Stefanov A, Kisic M, Živanov LD, Menicanin A. Design and Modelling of 3D Printed Capacitive Displacement Sensor. in Proceedings of the International Spring Seminar on Electronics Technology. 2021;2021-May.
doi:10.1109/ISSE51996.2021.9467666 .

Srdic, B., Stefanov, A., Kisic, M., Živanov, Ljiljana D, Menicanin, Aleksandar, "Design and Modelling of 3D Printed Capacitive Displacement Sensor" in Proceedings of the International Spring Seminar on Electronics Technology, 2021-May (2021),
https://doi.org/10.1109/ISSE51996.2021.9467666 . .

TY  - CONF
AU  - Kisic, M.
AU  - Živanov, Ljiljana D
AU  - Blaz, Nelu V.
AU  - Stefanov, A.
AU  - Menicanin, Aleksandar
PY  - 2020
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1307
AB  - This paper investigates the dielectric characteristics of the material used to make capacitor in fused filament fabrication technology. The characteristics of the capacitor made of PLA (Polylactic Acid) as dielectric are examined. Using a 3D printer, dielectric samples are created in the form of a disk 8.6 mm in diameter. Preliminary samples revealed that the surfaces of the printed samples are rough, after which the mechanical treatment of the samples is applied. The thicknesses of the samples belbre and after polishing are 1 mm and 0.7 mm, respectively. Epoxy electrodes are applied to the dielectric disks on both surfaces to produce the parallel plate capacitors. The capacitance of the fabricated capacitors is measured in the low frequency range, from 0.1 Hz to 200 kHz. The dissipation characteristics of the capacitor are examined, and a measured average value of tangent loss is 0.007. The printed dielectric samples without the electrodes are used to investigate their ability to withstand voltages up to 6 kV. The measurement results confirmed that the used PLA material is suitable for the fabrication of he capacitor with good characteristics.
PB  - IEEE Computer Society
C3  - Proceedings of the International Spring Seminar on Electronics Technology
T1  - Investigation of Dielectric Properties of Printed Material for Capacitor Application
VL  - 2020-May
DO  - 10.1109/ISSE49702.2020.9120980
ER  - 

@conference{
author = "Kisic, M. and Živanov, Ljiljana D and Blaz, Nelu V. and Stefanov, A. and Menicanin, Aleksandar",
year = "2020",
abstract = "This paper investigates the dielectric characteristics of the material used to make capacitor in fused filament fabrication technology. The characteristics of the capacitor made of PLA (Polylactic Acid) as dielectric are examined. Using a 3D printer, dielectric samples are created in the form of a disk 8.6 mm in diameter. Preliminary samples revealed that the surfaces of the printed samples are rough, after which the mechanical treatment of the samples is applied. The thicknesses of the samples belbre and after polishing are 1 mm and 0.7 mm, respectively. Epoxy electrodes are applied to the dielectric disks on both surfaces to produce the parallel plate capacitors. The capacitance of the fabricated capacitors is measured in the low frequency range, from 0.1 Hz to 200 kHz. The dissipation characteristics of the capacitor are examined, and a measured average value of tangent loss is 0.007. The printed dielectric samples without the electrodes are used to investigate their ability to withstand voltages up to 6 kV. The measurement results confirmed that the used PLA material is suitable for the fabrication of he capacitor with good characteristics.",
publisher = "IEEE Computer Society",
journal = "Proceedings of the International Spring Seminar on Electronics Technology",
title = "Investigation of Dielectric Properties of Printed Material for Capacitor Application",
volume = "2020-May",
doi = "10.1109/ISSE49702.2020.9120980"
}

Kisic, M., Živanov, L. D., Blaz, N. V., Stefanov, A.,& Menicanin, A.. (2020). Investigation of Dielectric Properties of Printed Material for Capacitor Application. in Proceedings of the International Spring Seminar on Electronics Technology
IEEE Computer Society., 2020-May.
https://doi.org/10.1109/ISSE49702.2020.9120980

Kisic M, Živanov LD, Blaz NV, Stefanov A, Menicanin A. Investigation of Dielectric Properties of Printed Material for Capacitor Application. in Proceedings of the International Spring Seminar on Electronics Technology. 2020;2020-May.
doi:10.1109/ISSE49702.2020.9120980 .

Kisic, M., Živanov, Ljiljana D, Blaz, Nelu V., Stefanov, A., Menicanin, Aleksandar, "Investigation of Dielectric Properties of Printed Material for Capacitor Application" in Proceedings of the International Spring Seminar on Electronics Technology, 2020-May (2020),
https://doi.org/10.1109/ISSE49702.2020.9120980 . .

TY  - CONF
AU  - Zlebic, C.
AU  - Ivanisević, N.
AU  - Kisic, M.
AU  - Blaz, Nelu V.
AU  - Menicanin, Aleksandar
AU  - Živanov, Ljiljana D
AU  - Damnjanović, M.
PY  - 2014
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/746
AB  - In this paper we compared a resistive and capacitive strain gauge in terms of sensitivity and material cost, both printed with deposition material printer using silver nanoparticle ink on a flexible polyimide substrate. The resistive change due to strain was measured with a full Wheatstone bridge and a signal conditioning circuit, while the capacitance change was measured with the HP4194A impedance analyzer. Measured and derived strain gauge factor for resistive sensor was 1.10, and 0.91 for the capacitive sensor.
PB  - Institute of Electrical and Electronics Engineers Inc.
C3  - Proceedings of the International Conference on Microelectronics, ICM
T1  - Comparison of Resistive and Capacitive Strain Gauge Sensors Printed on Polyimide Substrate Using Ink-Jet Printing Technology
EP  - 144
SP  - 141
DO  - 10.1109/MIEL.2014.6842105
ER  - 

@conference{
author = "Zlebic, C. and Ivanisević, N. and Kisic, M. and Blaz, Nelu V. and Menicanin, Aleksandar and Živanov, Ljiljana D and Damnjanović, M.",
year = "2014",
abstract = "In this paper we compared a resistive and capacitive strain gauge in terms of sensitivity and material cost, both printed with deposition material printer using silver nanoparticle ink on a flexible polyimide substrate. The resistive change due to strain was measured with a full Wheatstone bridge and a signal conditioning circuit, while the capacitance change was measured with the HP4194A impedance analyzer. Measured and derived strain gauge factor for resistive sensor was 1.10, and 0.91 for the capacitive sensor.",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
journal = "Proceedings of the International Conference on Microelectronics, ICM",
title = "Comparison of Resistive and Capacitive Strain Gauge Sensors Printed on Polyimide Substrate Using Ink-Jet Printing Technology",
pages = "144-141",
doi = "10.1109/MIEL.2014.6842105"
}

Zlebic, C., Ivanisević, N., Kisic, M., Blaz, N. V., Menicanin, A., Živanov, L. D.,& Damnjanović, M.. (2014). Comparison of Resistive and Capacitive Strain Gauge Sensors Printed on Polyimide Substrate Using Ink-Jet Printing Technology. in Proceedings of the International Conference on Microelectronics, ICM
Institute of Electrical and Electronics Engineers Inc.., 141-144.
https://doi.org/10.1109/MIEL.2014.6842105

Zlebic C, Ivanisević N, Kisic M, Blaz NV, Menicanin A, Živanov LD, Damnjanović M. Comparison of Resistive and Capacitive Strain Gauge Sensors Printed on Polyimide Substrate Using Ink-Jet Printing Technology. in Proceedings of the International Conference on Microelectronics, ICM. 2014;:141-144.
doi:10.1109/MIEL.2014.6842105 .

Zlebic, C., Ivanisević, N., Kisic, M., Blaz, Nelu V., Menicanin, Aleksandar, Živanov, Ljiljana D, Damnjanović, M., "Comparison of Resistive and Capacitive Strain Gauge Sensors Printed on Polyimide Substrate Using Ink-Jet Printing Technology" in Proceedings of the International Conference on Microelectronics, ICM (2014):141-144,
https://doi.org/10.1109/MIEL.2014.6842105 . .

TY  - CONF
AU  - Kisic, M.
AU  - Dakic, B.
AU  - Damnjanović, M.
AU  - Menicanin, Aleksandar
AU  - Blaz, Nelu V.
AU  - Živanov, Ljiljana D
PY  - 2013
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/715
AB  - This paper presents design, modeling and simulation cost-effective RFID (Radio Frequency Identification) tag using ink-jet printing technology. Passive 13.56 MHz RFID tag is based on an inductive-capacitive resonant circuit. Designed RFID tag is part of the ID (Identification) card, which has standard ISO ID1 size (85.60 mm x 53.98 mm). It consists of rectangular spiral planar inductor (antenna) and interdigital capacitor. The modeling and optimization of RFID tag are discussed. At the first step, inductor and capacitor were designed using in-house developed simulation tools AntInd and INDICON, respectively, in order to provide proper electrical characteristics of tag. After that, the designed geometrical structures are modeled and simulated using CST Microwave Studio software. A radiation pattern at operational frequency of 13.56 MHz simulated in CST of the RFID tag insulated in free spaces is presented.
PB  - IEEE
C3  - Proceedings of the International Spring Seminar on Electronics Technology
T1  - Design and Simulation of 13.56 MHz RFID Tag in Ink-Jet Printing Technology
EP  - 267
SP  - 263
DO  - 10.1109/ISSE.2013.6648254
ER  - 

@conference{
author = "Kisic, M. and Dakic, B. and Damnjanović, M. and Menicanin, Aleksandar and Blaz, Nelu V. and Živanov, Ljiljana D",
year = "2013",
abstract = "This paper presents design, modeling and simulation cost-effective RFID (Radio Frequency Identification) tag using ink-jet printing technology. Passive 13.56 MHz RFID tag is based on an inductive-capacitive resonant circuit. Designed RFID tag is part of the ID (Identification) card, which has standard ISO ID1 size (85.60 mm x 53.98 mm). It consists of rectangular spiral planar inductor (antenna) and interdigital capacitor. The modeling and optimization of RFID tag are discussed. At the first step, inductor and capacitor were designed using in-house developed simulation tools AntInd and INDICON, respectively, in order to provide proper electrical characteristics of tag. After that, the designed geometrical structures are modeled and simulated using CST Microwave Studio software. A radiation pattern at operational frequency of 13.56 MHz simulated in CST of the RFID tag insulated in free spaces is presented.",
publisher = "IEEE",
journal = "Proceedings of the International Spring Seminar on Electronics Technology",
title = "Design and Simulation of 13.56 MHz RFID Tag in Ink-Jet Printing Technology",
pages = "267-263",
doi = "10.1109/ISSE.2013.6648254"
}

Kisic, M., Dakic, B., Damnjanović, M., Menicanin, A., Blaz, N. V.,& Živanov, L. D.. (2013). Design and Simulation of 13.56 MHz RFID Tag in Ink-Jet Printing Technology. in Proceedings of the International Spring Seminar on Electronics Technology
IEEE., 263-267.
https://doi.org/10.1109/ISSE.2013.6648254

Kisic M, Dakic B, Damnjanović M, Menicanin A, Blaz NV, Živanov LD. Design and Simulation of 13.56 MHz RFID Tag in Ink-Jet Printing Technology. in Proceedings of the International Spring Seminar on Electronics Technology. 2013;:263-267.
doi:10.1109/ISSE.2013.6648254 .

Kisic, M., Dakic, B., Damnjanović, M., Menicanin, Aleksandar, Blaz, Nelu V., Živanov, Ljiljana D, "Design and Simulation of 13.56 MHz RFID Tag in Ink-Jet Printing Technology" in Proceedings of the International Spring Seminar on Electronics Technology (2013):263-267,
https://doi.org/10.1109/ISSE.2013.6648254 . .