TY  - CONF
AU  - Luković, Miloljub
AU  - Nikolić, Maria Vesna
AU  - Balaz, Nelu
AU  - Milutinov, Miodrag
AU  - Vasiljević, Zorka Z
AU  - Labus, Nebojša J.
AU  - Aleksić, Obrad S.
PY  - 2017
UR  - https://dais.sanu.ac.rs/123456789/15430
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1636
AB  - Starting hematite (Fe2O3), zinc oxide (ZnO) and manganese carbonate (MnCO3) powders were homogenized in a planetary ball mill in stainless steel bowls with stainless steel balls for 15 min, calcined in air at 1000 C for 2 h, milled in a planetary ball mill for 30 minutes, followed by 4 h in an aghate mill, sieved through a 325 mesh to form four starting powders: MnFe2O4, ZnFe2O4, Mn0.5Zn0.5Fe2O4 and a two-phase mixture of zinc and manganese ferrite. Structural properties of the obtained powders were analyzed using XRD, SEM and EDS. Electrical properties of disk shaped samples were measured at room temperature on an impedance analyzer in the frequency range 100 to 40 MHz, enabling determination and comparison of dielectric permittivity and complex impedance. Complex relative permeability of toroid shaped samples was measured on an impedance analyzer in the frequency range from 1 MHz to 500 MHz.
PB  - Belgrade : Institute for Multidisciplinary Research of the University of Belgrade
C3  - Programme and the Book of Abstracts / 4th Conference of The Serbian Society for Ceramic Materials, 4CSCS-2017, June 14-16, 2017, Belgrade, Serbia
T1  - Structural, electrical and magnetic properties of mechanically activated manganese and zinc ferrite
EP  - 102
SP  - 102
UR  - https://hdl.handle.net/21.15107/rcub_dais_15430
ER  - 

@conference{
author = "Luković, Miloljub and Nikolić, Maria Vesna and Balaz, Nelu and Milutinov, Miodrag and Vasiljević, Zorka Z and Labus, Nebojša J. and Aleksić, Obrad S.",
year = "2017",
abstract = "Starting hematite (Fe2O3), zinc oxide (ZnO) and manganese carbonate (MnCO3) powders were homogenized in a planetary ball mill in stainless steel bowls with stainless steel balls for 15 min, calcined in air at 1000 C for 2 h, milled in a planetary ball mill for 30 minutes, followed by 4 h in an aghate mill, sieved through a 325 mesh to form four starting powders: MnFe2O4, ZnFe2O4, Mn0.5Zn0.5Fe2O4 and a two-phase mixture of zinc and manganese ferrite. Structural properties of the obtained powders were analyzed using XRD, SEM and EDS. Electrical properties of disk shaped samples were measured at room temperature on an impedance analyzer in the frequency range 100 to 40 MHz, enabling determination and comparison of dielectric permittivity and complex impedance. Complex relative permeability of toroid shaped samples was measured on an impedance analyzer in the frequency range from 1 MHz to 500 MHz.",
publisher = "Belgrade : Institute for Multidisciplinary Research of the University of Belgrade",
journal = "Programme and the Book of Abstracts / 4th Conference of The Serbian Society for Ceramic Materials, 4CSCS-2017, June 14-16, 2017, Belgrade, Serbia",
title = "Structural, electrical and magnetic properties of mechanically activated manganese and zinc ferrite",
pages = "102-102",
url = "https://hdl.handle.net/21.15107/rcub_dais_15430"
}

Luković, M., Nikolić, M. V., Balaz, N., Milutinov, M., Vasiljević, Z. Z., Labus, N. J.,& Aleksić, O. S.. (2017). Structural, electrical and magnetic properties of mechanically activated manganese and zinc ferrite. in Programme and the Book of Abstracts / 4th Conference of The Serbian Society for Ceramic Materials, 4CSCS-2017, June 14-16, 2017, Belgrade, Serbia
Belgrade : Institute for Multidisciplinary Research of the University of Belgrade., 102-102.
https://hdl.handle.net/21.15107/rcub_dais_15430

Luković M, Nikolić MV, Balaz N, Milutinov M, Vasiljević ZZ, Labus NJ, Aleksić OS. Structural, electrical and magnetic properties of mechanically activated manganese and zinc ferrite. in Programme and the Book of Abstracts / 4th Conference of The Serbian Society for Ceramic Materials, 4CSCS-2017, June 14-16, 2017, Belgrade, Serbia. 2017;:102-102.
https://hdl.handle.net/21.15107/rcub_dais_15430 .

Luković, Miloljub, Nikolić, Maria Vesna, Balaz, Nelu, Milutinov, Miodrag, Vasiljević, Zorka Z, Labus, Nebojša J., Aleksić, Obrad S., "Structural, electrical and magnetic properties of mechanically activated manganese and zinc ferrite" in Programme and the Book of Abstracts / 4th Conference of The Serbian Society for Ceramic Materials, 4CSCS-2017, June 14-16, 2017, Belgrade, Serbia (2017):102-102,
https://hdl.handle.net/21.15107/rcub_dais_15430 .

TY  - CONF
AU  - Vasiljević, Zorka Z
AU  - Aleksić, Obrad S.
AU  - Luković, Miloljub D.
AU  - Vujković, Milica
AU  - Pavlović, Vladimir B
AU  - Labus, Nebojša
AU  - Nikolić, Maria Vesna
PY  - 2016
AB  - Pseudobrookite paste was composed of a mixture of starting nanopowders of hematite (α-Fe2O3) and anatase (TiO2) in the molar ratio 1:1.5, organic vehicle and glass frit. The paste was screen printed on on fluorine-doped tin oxide (FTO) glass substrate using screen printing technology. Structural, morphological and optical studies have been carried out using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and transmission electron microscopy (TEM). The photo-electrochemical performance of Fe2TiO5 screen printed thick film was examined under xenon lamp illumination in 1 M NaOH electrolyte.
PB  - Belgrade : Institute of Technical Sciences of the Serbian Academz of Sciences and Arts
C3  - Program and the Book of Abstracts / Fifteenth Young Researchers' Conference Materials Sciences and Engineering, December 7-9, 2016, Belgrade, 2016, 45-45
T1  - Fabrication, characterization and photoelectrochemical behavior of Fe2TiO5 screen printed thick films
UR  - https://hdl.handle.net/21.15107/rcub_rimsi_1109
ER  - 

@conference{
author = "Vasiljević, Zorka Z and Aleksić, Obrad S. and Luković, Miloljub D. and Vujković, Milica and Pavlović, Vladimir B and Labus, Nebojša and Nikolić, Maria Vesna",
year = "2016",
abstract = "Pseudobrookite paste was composed of a mixture of starting nanopowders of hematite (α-Fe2O3) and anatase (TiO2) in the molar ratio 1:1.5, organic vehicle and glass frit. The paste was screen printed on on fluorine-doped tin oxide (FTO) glass substrate using screen printing technology. Structural, morphological and optical studies have been carried out using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and transmission electron microscopy (TEM). The photo-electrochemical performance of Fe2TiO5 screen printed thick film was examined under xenon lamp illumination in 1 M NaOH electrolyte.",
publisher = "Belgrade : Institute of Technical Sciences of the Serbian Academz of Sciences and Arts",
journal = "Program and the Book of Abstracts / Fifteenth Young Researchers' Conference Materials Sciences and Engineering, December 7-9, 2016, Belgrade, 2016, 45-45",
title = "Fabrication, characterization and photoelectrochemical behavior of Fe2TiO5 screen printed thick films",
url = "https://hdl.handle.net/21.15107/rcub_rimsi_1109"
}

Vasiljević, Z. Z., Aleksić, O. S., Luković, M. D., Vujković, M., Pavlović, V. B., Labus, N.,& Nikolić, M. V.. (2016). Fabrication, characterization and photoelectrochemical behavior of Fe2TiO5 screen printed thick films. in Program and the Book of Abstracts / Fifteenth Young Researchers' Conference Materials Sciences and Engineering, December 7-9, 2016, Belgrade, 2016, 45-45
Belgrade : Institute of Technical Sciences of the Serbian Academz of Sciences and Arts..
https://hdl.handle.net/21.15107/rcub_rimsi_1109

Vasiljević ZZ, Aleksić OS, Luković MD, Vujković M, Pavlović VB, Labus N, Nikolić MV. Fabrication, characterization and photoelectrochemical behavior of Fe2TiO5 screen printed thick films. in Program and the Book of Abstracts / Fifteenth Young Researchers' Conference Materials Sciences and Engineering, December 7-9, 2016, Belgrade, 2016, 45-45. 2016;.
https://hdl.handle.net/21.15107/rcub_rimsi_1109 .

Vasiljević, Zorka Z, Aleksić, Obrad S., Luković, Miloljub D., Vujković, Milica, Pavlović, Vladimir B, Labus, Nebojša, Nikolić, Maria Vesna, "Fabrication, characterization and photoelectrochemical behavior of Fe2TiO5 screen printed thick films" in Program and the Book of Abstracts / Fifteenth Young Researchers' Conference Materials Sciences and Engineering, December 7-9, 2016, Belgrade, 2016, 45-45 (2016),
https://hdl.handle.net/21.15107/rcub_rimsi_1109 .

TY  - CONF
AU  - Aleksić, Obrad S.
AU  - Milutinov, Predrag
AU  - Nikolić, Maria Vesna
AU  - Blaž, Nelu
AU  - Luković, Miloljub
AU  - Vasiljević, Zorka Z
AU  - Marković, Smilja
AU  - Živanov, Ljiljana D
PY  - 2015
UR  - https://dais.sanu.ac.rs/123456789/15427
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1635
AB  - Commercial Mn-Zn ferrite powder was milled in a planetary ball mill for 30-240 minutes. Particle size distribution in the milled powders was analyzed using a laser particle size analyzer and correlated with XRD and SEM analysis of the milled powders. Green disc and torroid samples were sintered in air in the temperature interval 800 -1300oC for 2 hours. SEM/EDS, AFM/MFM analysis of the sintered samples and measurements of their electrical properties such as DC resistance up to 500 MHz enabled establishment of a correlation between the microstructure and properties in the high-frequency range.
PB  - Belgrade : Institute for Multidisciplinary Research, University of Belgrade
C3  - Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia
T1  - Tailoring the microstructure of Mn-Zn ferrite to electronic properties
EP  - 101
SP  - 101
UR  - https://hdl.handle.net/21.15107/rcub_dais_15427
ER  - 

@conference{
author = "Aleksić, Obrad S. and Milutinov, Predrag and Nikolić, Maria Vesna and Blaž, Nelu and Luković, Miloljub and Vasiljević, Zorka Z and Marković, Smilja and Živanov, Ljiljana D",
year = "2015",
abstract = "Commercial Mn-Zn ferrite powder was milled in a planetary ball mill for 30-240 minutes. Particle size distribution in the milled powders was analyzed using a laser particle size analyzer and correlated with XRD and SEM analysis of the milled powders. Green disc and torroid samples were sintered in air in the temperature interval 800 -1300oC for 2 hours. SEM/EDS, AFM/MFM analysis of the sintered samples and measurements of their electrical properties such as DC resistance up to 500 MHz enabled establishment of a correlation between the microstructure and properties in the high-frequency range.",
publisher = "Belgrade : Institute for Multidisciplinary Research, University of Belgrade",
journal = "Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia",
title = "Tailoring the microstructure of Mn-Zn ferrite to electronic properties",
pages = "101-101",
url = "https://hdl.handle.net/21.15107/rcub_dais_15427"
}

Aleksić, O. S., Milutinov, P., Nikolić, M. V., Blaž, N., Luković, M., Vasiljević, Z. Z., Marković, S.,& Živanov, L. D.. (2015). Tailoring the microstructure of Mn-Zn ferrite to electronic properties. in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia
Belgrade : Institute for Multidisciplinary Research, University of Belgrade., 101-101.
https://hdl.handle.net/21.15107/rcub_dais_15427

Aleksić OS, Milutinov P, Nikolić MV, Blaž N, Luković M, Vasiljević ZZ, Marković S, Živanov LD. Tailoring the microstructure of Mn-Zn ferrite to electronic properties. in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia. 2015;:101-101.
https://hdl.handle.net/21.15107/rcub_dais_15427 .

Aleksić, Obrad S., Milutinov, Predrag, Nikolić, Maria Vesna, Blaž, Nelu, Luković, Miloljub, Vasiljević, Zorka Z, Marković, Smilja, Živanov, Ljiljana D, "Tailoring the microstructure of Mn-Zn ferrite to electronic properties" in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia (2015):101-101,
https://hdl.handle.net/21.15107/rcub_dais_15427 .

TY  - CONF
AU  - Vasiljević, Zorka Z
AU  - Nikolić, Maria Vesna
AU  - Aleksić, Obrad S.
AU  - Labus, Nebojša J.
AU  - Luković, Miloljub
AU  - Marković, Smilja
AU  - Nikolić, Pantelija M.
PY  - 2015
UR  - https://dais.sanu.ac.rs/123456789/15425
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1633
AB  - Starting powders of TiO2 (anatase) and Fe2O3 (hematite) were mixed in the molar ratio 1:1. Pseudobrookite powder was obtained by a combined milling/calcination procedure. Particle size distribution was analyzed on a laser particle size analyzer and correlated with XRD and SEM analysis. The band gap was determined using UV/Vis spectroscopy. Green samples were sintered in a dilatometer and at 1000oC for 2h in air. Thermal diffusivity was determined from photoacoustic measurements. Electrical conductivity measurements were performed. The aim was to obtain pseudobrookite with properties suitable for polymer paste for thick films to be applied as gas sensors.
PB  - Belgrade : Institute for Multidisciplinary Research, University of Belgrade
C3  - Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia
T1  - Structural and Electronic Properties of Pseudobrookite
EP  - 99
SP  - 98
UR  - https://hdl.handle.net/21.15107/rcub_dais_15425
ER  - 

@conference{
author = "Vasiljević, Zorka Z and Nikolić, Maria Vesna and Aleksić, Obrad S. and Labus, Nebojša J. and Luković, Miloljub and Marković, Smilja and Nikolić, Pantelija M.",
year = "2015",
abstract = "Starting powders of TiO2 (anatase) and Fe2O3 (hematite) were mixed in the molar ratio 1:1. Pseudobrookite powder was obtained by a combined milling/calcination procedure. Particle size distribution was analyzed on a laser particle size analyzer and correlated with XRD and SEM analysis. The band gap was determined using UV/Vis spectroscopy. Green samples were sintered in a dilatometer and at 1000oC for 2h in air. Thermal diffusivity was determined from photoacoustic measurements. Electrical conductivity measurements were performed. The aim was to obtain pseudobrookite with properties suitable for polymer paste for thick films to be applied as gas sensors.",
publisher = "Belgrade : Institute for Multidisciplinary Research, University of Belgrade",
journal = "Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia",
title = "Structural and Electronic Properties of Pseudobrookite",
pages = "99-98",
url = "https://hdl.handle.net/21.15107/rcub_dais_15425"
}

Vasiljević, Z. Z., Nikolić, M. V., Aleksić, O. S., Labus, N. J., Luković, M., Marković, S.,& Nikolić, P. M.. (2015). Structural and Electronic Properties of Pseudobrookite. in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia
Belgrade : Institute for Multidisciplinary Research, University of Belgrade., 98-99.
https://hdl.handle.net/21.15107/rcub_dais_15425

Vasiljević ZZ, Nikolić MV, Aleksić OS, Labus NJ, Luković M, Marković S, Nikolić PM. Structural and Electronic Properties of Pseudobrookite. in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia. 2015;:98-99.
https://hdl.handle.net/21.15107/rcub_dais_15425 .

Vasiljević, Zorka Z, Nikolić, Maria Vesna, Aleksić, Obrad S., Labus, Nebojša J., Luković, Miloljub, Marković, Smilja, Nikolić, Pantelija M., "Structural and Electronic Properties of Pseudobrookite" in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia (2015):98-99,
https://hdl.handle.net/21.15107/rcub_dais_15425 .

TY  - CONF
AU  - Vasiljević, Zorka Z
AU  - Aleksić, Obrad S.
AU  - Nikolić, Maria Vesna
PY  - 2013
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1640
AB  - Starting nanopowders of TiO2 (anatase 99.7%) and a-Fe2O3 (hematite) were mixed in the weight ratio 60:40 and 40:60. Green samples were sintered in the temperature range 750-1250oC in air. Structural, morphological and electrical studies were carried out using XRD, SEM and EDS analysis and Hall measurements with the aim of analyzing the influence of the starting nanopowder structure on the resulting sample composition, density, grain size and electrical resistivity. Compared to pure anatase samples, the presence of hematite lowered the temperature of completion of the anatase to rutile phase transformation to 850oC. Formation of pseudobrookite was also noted at this temperature. Further increase in the sintering temperature lead to increase in sample density and grain size and decrease in the electric resistivity, Hall coefficient and mobility.
PB  - Belgrade : Institute of Technical Sciences of SASA
C3  - Program and the Book of Abstracts / Twelfth Young Researchers' Conference Materials Sciences and Engineering December 11-13, 2013, Belgrade, Serbia
T1  - 3 Structural, morphological and electrical properties of sintered Fe2O3/TiO2 nanopowder mixtures
EP  - 36
SP  - 36
UR  - https://hdl.handle.net/21.15107/rcub_dais_447
ER  - 

@conference{
author = "Vasiljević, Zorka Z and Aleksić, Obrad S. and Nikolić, Maria Vesna",
year = "2013",
abstract = "Starting nanopowders of TiO2 (anatase 99.7%) and a-Fe2O3 (hematite) were mixed in the weight ratio 60:40 and 40:60. Green samples were sintered in the temperature range 750-1250oC in air. Structural, morphological and electrical studies were carried out using XRD, SEM and EDS analysis and Hall measurements with the aim of analyzing the influence of the starting nanopowder structure on the resulting sample composition, density, grain size and electrical resistivity. Compared to pure anatase samples, the presence of hematite lowered the temperature of completion of the anatase to rutile phase transformation to 850oC. Formation of pseudobrookite was also noted at this temperature. Further increase in the sintering temperature lead to increase in sample density and grain size and decrease in the electric resistivity, Hall coefficient and mobility.",
publisher = "Belgrade : Institute of Technical Sciences of SASA",
journal = "Program and the Book of Abstracts / Twelfth Young Researchers' Conference Materials Sciences and Engineering December 11-13, 2013, Belgrade, Serbia",
title = "3 Structural, morphological and electrical properties of sintered Fe2O3/TiO2 nanopowder mixtures",
pages = "36-36",
url = "https://hdl.handle.net/21.15107/rcub_dais_447"
}

Vasiljević, Z. Z., Aleksić, O. S.,& Nikolić, M. V.. (2013). 3 Structural, morphological and electrical properties of sintered Fe2O3/TiO2 nanopowder mixtures. in Program and the Book of Abstracts / Twelfth Young Researchers' Conference Materials Sciences and Engineering December 11-13, 2013, Belgrade, Serbia
Belgrade : Institute of Technical Sciences of SASA., 36-36.
https://hdl.handle.net/21.15107/rcub_dais_447

Vasiljević ZZ, Aleksić OS, Nikolić MV. 3 Structural, morphological and electrical properties of sintered Fe2O3/TiO2 nanopowder mixtures. in Program and the Book of Abstracts / Twelfth Young Researchers' Conference Materials Sciences and Engineering December 11-13, 2013, Belgrade, Serbia. 2013;:36-36.
https://hdl.handle.net/21.15107/rcub_dais_447 .

Vasiljević, Zorka Z, Aleksić, Obrad S., Nikolić, Maria Vesna, "3 Structural, morphological and electrical properties of sintered Fe2O3/TiO2 nanopowder mixtures" in Program and the Book of Abstracts / Twelfth Young Researchers' Conference Materials Sciences and Engineering December 11-13, 2013, Belgrade, Serbia (2013):36-36,
https://hdl.handle.net/21.15107/rcub_dais_447 .

TY  - CONF
AU  - Đurić, Zorka Z
AU  - Aleksić, Obrad S.
AU  - Nikolić, Maria Vesna
AU  - Branković, Goran
AU  - Nikolić, Pantelija M.
PY  - 2013
AB  - Thick films of nanostructured TiO2 (60 wt%) and alpha-Fe2O3 (40 wt%) were fabricated by screen printing technology on an alumina substrate. Samples were sintered in the temperature range 750-1350oC in air. Thick film paste was obtained by mixing anatase and hematite nanopowders in the ratio 3:2, an organic vehicle and binding glass frit. Structural, morphological and optical studies were carried out using XRD, SEM and EDS analysis and UV/Vis spectroscopy enabling correlation between optical and structural changes with the aim of applying the fabricated thick films as anodes in hotoelectrochemical cells for hydrogen generation and water splitting.
PB  - Bor : Technical Faculty
C3  - 45th International October Conference on Mining and Metallurgy - IOC 2013, 16-19 October 2013, Bor, Serbia : Proceedings, 2013
T1  - Structural, morphological and optical study of nanostructured TiO2/Fe2O3 thick film
EP  - 1570
SP  - 1566
UR  - https://hdl.handle.net/21.15107/rcub_rimsi_157
ER  - 

@conference{
author = "Đurić, Zorka Z and Aleksić, Obrad S. and Nikolić, Maria Vesna and Branković, Goran and Nikolić, Pantelija M.",
year = "2013",
abstract = "Thick films of nanostructured TiO2 (60 wt%) and alpha-Fe2O3 (40 wt%) were fabricated by screen printing technology on an alumina substrate. Samples were sintered in the temperature range 750-1350oC in air. Thick film paste was obtained by mixing anatase and hematite nanopowders in the ratio 3:2, an organic vehicle and binding glass frit. Structural, morphological and optical studies were carried out using XRD, SEM and EDS analysis and UV/Vis spectroscopy enabling correlation between optical and structural changes with the aim of applying the fabricated thick films as anodes in hotoelectrochemical cells for hydrogen generation and water splitting.",
publisher = "Bor : Technical Faculty",
journal = "45th International October Conference on Mining and Metallurgy - IOC 2013, 16-19 October 2013, Bor, Serbia : Proceedings, 2013",
title = "Structural, morphological and optical study of nanostructured TiO2/Fe2O3 thick film",
pages = "1570-1566",
url = "https://hdl.handle.net/21.15107/rcub_rimsi_157"
}

Đurić, Z. Z., Aleksić, O. S., Nikolić, M. V., Branković, G.,& Nikolić, P. M.. (2013). Structural, morphological and optical study of nanostructured TiO2/Fe2O3 thick film. in 45th International October Conference on Mining and Metallurgy - IOC 2013, 16-19 October 2013, Bor, Serbia : Proceedings, 2013
Bor : Technical Faculty., 1566-1570.
https://hdl.handle.net/21.15107/rcub_rimsi_157

Đurić ZZ, Aleksić OS, Nikolić MV, Branković G, Nikolić PM. Structural, morphological and optical study of nanostructured TiO2/Fe2O3 thick film. in 45th International October Conference on Mining and Metallurgy - IOC 2013, 16-19 October 2013, Bor, Serbia : Proceedings, 2013. 2013;:1566-1570.
https://hdl.handle.net/21.15107/rcub_rimsi_157 .

Đurić, Zorka Z, Aleksić, Obrad S., Nikolić, Maria Vesna, Branković, Goran, Nikolić, Pantelija M., "Structural, morphological and optical study of nanostructured TiO2/Fe2O3 thick film" in 45th International October Conference on Mining and Metallurgy - IOC 2013, 16-19 October 2013, Bor, Serbia : Proceedings, 2013 (2013):1566-1570,
https://hdl.handle.net/21.15107/rcub_rimsi_157 .

TY  - CONF
AU  - Nikolić, Maria Vesna
AU  - Slankamenac, Miloš
AU  - Nikolić, N.
AU  - Sekulić, D. I.
AU  - Aleksić, Obrad S.
AU  - Mitrić, Miodrag
AU  - Ivetić, Tamara B.
AU  - Pavlović, Vladimir B
AU  - Nikolić, Pantelija M.
PY  - 2012
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/1641
AB  - The effects of Zn-doping on the dielectric behavior and electrical properties of bulk alpha-Fe2O3 have been studied. X-ray diffraction analysis revealed the presence of two phases in all samples: hematite and spinel ZnFe2O4, with the amount of spinel phase increasing with increasing Zn content. Scanning electron microscopy analysis combined with energy dispersive X-ray spectroscopy showed that the Zn-bearing phase occurred in the form of individual spinel ZnFe2O4 grains in a hematite matrix. DC conductivity was measured in the temperature range 25-225°C (298-498 K). Impedance spectroscopy measurements in the same temperature range were carried out in the frequency range 100Hz to 10 MHz. Increase in the Zn content resulted in increased electrical conductivity and higher values of the dielectric constant. The resistance and capacitance of grains and grain boundaries were analyzed by modeling the experimental results using an equivalent circuit.
PB  - Belgrade : Serbian Ceramic Society
C3  - The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts
T1  - Study of Dielectric Behavior and Electrical Properties of Hematite a-Fe2O3 Doped with Zn
EP  - 8
SP  - 8
UR  - https://hdl.handle.net/21.15107/rcub_dais_523
ER  - 

@conference{
author = "Nikolić, Maria Vesna and Slankamenac, Miloš and Nikolić, N. and Sekulić, D. I. and Aleksić, Obrad S. and Mitrić, Miodrag and Ivetić, Tamara B. and Pavlović, Vladimir B and Nikolić, Pantelija M.",
year = "2012",
abstract = "The effects of Zn-doping on the dielectric behavior and electrical properties of bulk alpha-Fe2O3 have been studied. X-ray diffraction analysis revealed the presence of two phases in all samples: hematite and spinel ZnFe2O4, with the amount of spinel phase increasing with increasing Zn content. Scanning electron microscopy analysis combined with energy dispersive X-ray spectroscopy showed that the Zn-bearing phase occurred in the form of individual spinel ZnFe2O4 grains in a hematite matrix. DC conductivity was measured in the temperature range 25-225°C (298-498 K). Impedance spectroscopy measurements in the same temperature range were carried out in the frequency range 100Hz to 10 MHz. Increase in the Zn content resulted in increased electrical conductivity and higher values of the dielectric constant. The resistance and capacitance of grains and grain boundaries were analyzed by modeling the experimental results using an equivalent circuit.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts",
title = "Study of Dielectric Behavior and Electrical Properties of Hematite a-Fe2O3 Doped with Zn",
pages = "8-8",
url = "https://hdl.handle.net/21.15107/rcub_dais_523"
}

Nikolić, M. V., Slankamenac, M., Nikolić, N., Sekulić, D. I., Aleksić, O. S., Mitrić, M., Ivetić, T. B., Pavlović, V. B.,& Nikolić, P. M.. (2012). Study of Dielectric Behavior and Electrical Properties of Hematite a-Fe2O3 Doped with Zn. in The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts
Belgrade : Serbian Ceramic Society., 8-8.
https://hdl.handle.net/21.15107/rcub_dais_523

Nikolić MV, Slankamenac M, Nikolić N, Sekulić DI, Aleksić OS, Mitrić M, Ivetić TB, Pavlović VB, Nikolić PM. Study of Dielectric Behavior and Electrical Properties of Hematite a-Fe2O3 Doped with Zn. in The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts. 2012;:8-8.
https://hdl.handle.net/21.15107/rcub_dais_523 .

Nikolić, Maria Vesna, Slankamenac, Miloš, Nikolić, N., Sekulić, D. I., Aleksić, Obrad S., Mitrić, Miodrag, Ivetić, Tamara B., Pavlović, Vladimir B, Nikolić, Pantelija M., "Study of Dielectric Behavior and Electrical Properties of Hematite a-Fe2O3 Doped with Zn" in The First Serbian Ceramic Society Conference "Advanced Ceramics and Application" May 10-11, 2012: Program and the Book of Abstracts (2012):8-8,
https://hdl.handle.net/21.15107/rcub_dais_523 .

TY  - CONF
AU  - Luković, Miloljub D.
AU  - Blaž, Nelu
AU  - Nikolić, Maria Vesna
AU  - Menicanin, Aleksandar
AU  - Lukić, Lazar S
AU  - Živanov, Ljiljana D
AU  - Aleksić, Obrad S.
PY  - 2011
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/3158
AB  - Dobijanje čip induktora višeslojnom tehnologijom (spajanjem zelenih feritnih listova na kojima su naneti delovi namotaja štampanjem PdAg paste) opisano je u najkraćem. Svojstva MnZn ferita u EMI opsegu data su na osnovu merenja impedanse Z(ω) i proračuna realativne permeabilnosti μr i dielektrične konstante εr. Merenje impedanse čip induktora različitih dimenzija i konstrukcije vršeno je takoće u EMI opsegu. Paralelno su u istom frekventnom opsegu vršena merenja impedanse na malim jezgrima sa više otvora dobijenim presovanjem i sinterovnjem istog materijala. Za kvalitativno-kvantitativnu analizu kao model usvojeno je paralelno RLC kolo. Dobijeni rezultati upoređeni su međusobno i sa najboljim literaturnim rezultatima.
PB  - Društvo za ETRAN, Republika Srpska
C3  - ETRAN 2011, Društvo za ETRAN, Republika Srpska
T1  - Uporedna analiza promene impedanse višeslojnih čip induktora i malih jezgara sa više otvora u EMI opsegu
T1  - PARALLEL ANALYSIS OF IMPEDANCE CHANGE OF FERRITE MULTILAYER CHIP INDUCTORS AND SMALL MULTI-APERTURE CORES IN THE EMI RANGE
EP  - MO1.2-4
SP  - MO1.2-1
UR  - https://hdl.handle.net/21.15107/rcub_rimsi_3158
ER  - 

@conference{
author = "Luković, Miloljub D. and Blaž, Nelu and Nikolić, Maria Vesna and Menicanin, Aleksandar and Lukić, Lazar S and Živanov, Ljiljana D and Aleksić, Obrad S.",
year = "2011",
abstract = "Dobijanje čip induktora višeslojnom tehnologijom (spajanjem zelenih feritnih listova na kojima su naneti delovi namotaja štampanjem PdAg paste) opisano je u najkraćem. Svojstva MnZn ferita u EMI opsegu data su na osnovu merenja impedanse Z(ω) i proračuna realativne permeabilnosti μr i dielektrične konstante εr. Merenje impedanse čip induktora različitih dimenzija i konstrukcije vršeno je takoće u EMI opsegu. Paralelno su u istom frekventnom opsegu vršena merenja impedanse na malim jezgrima sa više otvora dobijenim presovanjem i sinterovnjem istog materijala. Za kvalitativno-kvantitativnu analizu kao model usvojeno je paralelno RLC kolo. Dobijeni rezultati upoređeni su međusobno i sa najboljim literaturnim rezultatima.",
publisher = "Društvo za ETRAN, Republika Srpska",
journal = "ETRAN 2011, Društvo za ETRAN, Republika Srpska",
title = "Uporedna analiza promene impedanse višeslojnih čip induktora i malih jezgara sa više otvora u EMI opsegu, PARALLEL ANALYSIS OF IMPEDANCE CHANGE OF FERRITE MULTILAYER CHIP INDUCTORS AND SMALL MULTI-APERTURE CORES IN THE EMI RANGE",
pages = "MO1.2-4-MO1.2-1",
url = "https://hdl.handle.net/21.15107/rcub_rimsi_3158"
}

Luković, M. D., Blaž, N., Nikolić, M. V., Menicanin, A., Lukić, L. S., Živanov, L. D.,& Aleksić, O. S.. (2011). Uporedna analiza promene impedanse višeslojnih čip induktora i malih jezgara sa više otvora u EMI opsegu. in ETRAN 2011, Društvo za ETRAN, Republika Srpska
Društvo za ETRAN, Republika Srpska., MO1.2-1-MO1.2-4.
https://hdl.handle.net/21.15107/rcub_rimsi_3158

Luković MD, Blaž N, Nikolić MV, Menicanin A, Lukić LS, Živanov LD, Aleksić OS. Uporedna analiza promene impedanse višeslojnih čip induktora i malih jezgara sa više otvora u EMI opsegu. in ETRAN 2011, Društvo za ETRAN, Republika Srpska. 2011;:MO1.2-1-MO1.2-4.
https://hdl.handle.net/21.15107/rcub_rimsi_3158 .

Luković, Miloljub D., Blaž, Nelu, Nikolić, Maria Vesna, Menicanin, Aleksandar, Lukić, Lazar S, Živanov, Ljiljana D, Aleksić, Obrad S., "Uporedna analiza promene impedanse višeslojnih čip induktora i malih jezgara sa više otvora u EMI opsegu" in ETRAN 2011, Društvo za ETRAN, Republika Srpska (2011):MO1.2-1-MO1.2-4,
https://hdl.handle.net/21.15107/rcub_rimsi_3158 .